Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
we are facing a weird issue with a few models of smartphone since we increased the max MTU size. We are testing at the office with the Xperia E6553 but the Samsung...
Hi there
I am stuck. My incremental wheel with photocell and comparator circuit does not work if the QDEC hangs on it. But seperately it works fine.
When I hang it to...
Hi Team,
Which models are supported in the latest mesh SDK?
I can see support for the on-off model.
Is Time and Scenes (Explained in Mesh Models.pdf, Section-5, Page...
I use SDK13, nRF52, S132
I use bootloader_secure_ble with generated public key for bootloader and for nrfutil. After all steps like discribed on
devzone.nordicsemi.com...
Hello.
I use nRF52832 and power from 3.3V source. Also I use the accelerometer and gyroscope with VDD 2.5V and 3.0V respectively. They are connected to nRF through SPI....
Can a device that is configured and programmed from Keil (softdevice, application, bootloader) be updated with code that has been compiled on ses (application)? I have converted...
Hi,
Referring to bootloader programming article - there's a post-build phase of programming UICR.BOOTLOADERADDR
The article describe how to use nrfjprog to do this which...
Hello,
I studied the "gpiote" example in the SDK. In order to fully understand how it works, I attempted to modify the "template_project" example and follow the process...
SDK：【nRF5_SDK_15.0.0_a53641a】【examples】【ble_peripheral】【ble_app_uart】【pca10056】【s140】【arm5_no_packs】
Before downloading nRF Connect ,the results of my scan is
【service1...
We are using SDK nRF5_SDK_13.0.0_04a0bfd with the NRF52832 chip. Using peripheral role, the nRF is fatal crashing right after connecting with iOS nRFConnect (and our custom...
Hello. I have discovered similar questions, but it's still not clear for me. I also have cheched pwr_mgmt example, but as I understand all operations with power mode in board...
I recently upgraded from SDK 11.0 to SDK 14.0 and am seeing much slower connection speeds from the new SDK. The old version would connect in about 400ms, but the new SDK takes...
I would like to measure the VDDH voltage (lithium ion battery) on a nrf52840 with the power fail comparator.
If the voltage drops below the threshold, I want to reduce the...
Hi all,
we are using NRF52810 and SDK 15.0 (our own custom board)
working on ble_app_uart.c example.
we are able to send / receive 20bytes(approx).
we need to transfer...
