Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Dear Nordic Team,
We are using nRF52832 with a IQS231A for proximity detection for a new product, the pins are connected to SDA and SCL and everything is routed as in...
I am now using nrf52832 sdk14.2 development, as a slave device, I want to set the slave's Bluetooth interval is 1S, I set the following parameters: #define MIN_CONN_INTERVAL...
Hello,
I have nRF52832 with custom board and using SDK15 with Keil uVISION 5. I am working on beacon example and I have modified it to show battery level. I have done necessary...
I am using the bootloader_secure_serial example from the SDK 14.0.0 on a 523832 DK. I have erased the device and flashed the softdevice and bootlader on it. The LED1 is turned...
Hey, I would love some guidance on this:
1. I have one NRF52840 advertising constantly at 8dbm, this device is connected to power so it's hard coded to the maximum transfer...
Greetings,
Based on your librairies/examples, I can succesfully write and read data from an external flash (MX25R6435F) using QSPI with DMA.
I'm using a custom board with...
Dear all
I am on the pca10040 board (nrf52832), and I see the "Thingy_bridge" program is pca20020 board, as shown in Figure 1;
I am in the burning process, the simulation...
hi, im using ble_app_uart and im trying to do a simple communication and data transfer over bluetooth with my iOS.i want to send from the Bluefruit app a byte (0x55 for example...
Hello,
I'm using IAR 8.22.1, SDK 15.0.0, S132, nRF Connect V4.19.2.
I've loaded the 'secure_bootloader' example to PCA10040 EVB.
The device is recognized as DFUTARG...
Need to pass data from a battery powered sensor to a PC via a RF link. Would prefer
a COM Port emulation at 115,200 Baud. I already have a pair of nRF52 Development
Kits...
Hi guys,
Going through mesh packet format today and I'm stumbling upon the time_required_to_send_us method in broadcast.c which is used to calculate and indicate how long...
Hi,
I read and tried Mesh DFU given in " DFU quick start guide of nRF5 SDK for Mesh v2.0.1".
It says "To perform DFU transfers over mesh, use a customized version of...
Hi team,
Is there a way to figure out the phone id (to identify the source of pairing) after the phone has paired with the nordic device?
Basically what we need is is...
Hello,
I've downloaded nRF mesh and installed it on my iPhone, I can use it to provision my device, but there is a question about how to import AppKey on it.
I clicked...
