Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I tried looking for an answer for this, however unsuccessfully. I have a custom characteristic and I set it with a string of values when it is added to the custom service...
Hi Everyone,
I'm having some trouble understanding the different combinations of low power modes and how to use them.
When I first power up my board I use about 500uA...
Hi team,
We are doing indoor navigation project using BLE nordic beacons and we are using ble_app_beacon as a transmitter.
We are calculating the position of person...
Hi there, i'm trying to connect to the internet from my nrf52 chip.
one way i think, we can use the ios as a shareing point for the embeded world.
And i tried from a win10...
Hello,
I have a Mesh application using the nRF5 Mesh SDK version 2.0.1.
I wish to implement the possibility for a node to forget its provisioning status and become unprovisioned...
Does the NRF51 DK come with a SWD interface connector-cable to plug into a PCB's SWD port when flashing/programming code into a WLCSP chip soldered onto the PCB? If not, are...
I'm trying to setup a simple host node to broadcast a attention message with no definitive destination node. I need any of the child nodes (primarily asleep) to see and process...
Hello everyone,
I tried to use the example project " ble_ant_app_hrm" SDKv14.2 but it doesn't work. The bluetooth connection work correctly, I connect my smartphone with...
Hello Nordic
I am developing our device. It uses SDK 14.2.0 and s332 SoftDevice.
This device communicate our app by using ble as peripherals.
I thought that our project...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
