Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I use pstorage to allocate 32bytes of memory with 2 block, means each block having 16 bytes, when I write 16byte data into block_0 portion, I am not able to go to the...
Hello,
I use the Segger J-link software with my PCA10001 and recently updated it to last version (v.5.1). After install it asked me to update the firmware to the last version...
Hello,
I'm trying to flash external nrf51422 module.
I want to flash both softdevice and application. I used below commands:
mergehex -m %SOFTDEVICE_NAME% %APP_NAME...
I want as much control over advertising as possible. Barring that, I want to understand why the softdevice automatically goes back into advertising after a GAP disconnect...
Hi,
Assume that we want to send a data array by putting it in consecutive advertisement packets. I know that data update has to be done by calling ble_advdata_set(...)...
Hi
I'm trying to implement battery level on my custom profile.
So I used battery.c and ble_bas.c files for the battery service from nodic's sdk nrf51822_v4.4.1.31827....
I have make over your bootloader example to create my own without BLE support in bootloader (new programs are send in application instead of in dfu bootloader). Bootloader...
Having some trouble using the NRF52 as RX and nrf24l01+ as TX. The NRF52 receives the packet, but for some reason it always says CRCerror.
Anyone ever tried to use NRF52...
Hey Guys,
In my custom board I need to use two different I2C bus and one SPI.
At the moment i'm using twi_master to comunicate with one of the TWI bus,
but to switch...
I have several nRF6930 beacon kits. Some have a sticker indicating they have a PCA10006 board, on others, the sticker indicates PCA20006. All PCBs are marked 400059 0138RUBR...
Dear developers,
As we know, nrf51 has a maximum flash erase / write cycles of 20.000 times. So, in my code, I have implemented a counter that checks if max. flash write...
Dear All,
Does it worth coding a selection (scanning?) of "relatively free" radio channel to stick to?
Say, before starting our distributed application (consider a network...
Hi,
The artical form this link is great !
devzone.nordicsemi.com/.../
but I've some interogations.
the clear text contains the nonce value; 12 random bytes starting...
