Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
We have experienced some unknown resets in our devices specifically when woken up after being in storage for a prolonged period in ULP mode - about a year or so. Afterwards...
Hello!
I'm writing an application that uses MQTT to post some sensor data to a server. My networking code is basically a duplicate of this sample , except I set up the LTE...
Hello -
I was nearing completion of a BLE Mesh project with the NRF52840 when there became a shortage of NRF52840 QFN. I decided to migrate back to the NRF52832 and reworked...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hi All,
I am exploring nrf54l15 which has rram 1524KB. However, noticed that not able to access beyond 1428KB.
When build sample hello world code found that only 1428KB...
I've testing out the GNSS and Location samples. According to documentation, A-GNSS is enabled by default in the location sample but I am not able to confirm this both through...
Good Afternoon,
I am working on getting the npm1300 up and running on my custom board. I have a 1v8 line and a 3v2 line with the load switches being used as LDOs. I am using...
Hi,
I'm working on an indoor positioning system using an nRF5340 and a CHW1010-ANT1 antenna array. I'm receiving IQ samples from BLE CTE packets and using them to calculate...
While using the nRF9151 DK , after inserting the onomondo sim and connecting, the Cellular Monitor SIM sections appears the Wireless Logic ICCID number instead of onomondo...
Hi,
We are developing a product with WIFI+BLE and we are using nRF7002DK as the base. The important function is OTA because our functions may be changed after the hardware...
Hello,
I used to be working with the nrf sdk 2.7.0. For running unit tests for my project I build and run the unit test application for qemu_cortex_m3 like this:
...
Hi i am facing the issue with initializing the peripherals when the device is wake up from the deep sleep this are the logs i am getting after wake up this taking to log to...
Hello,
We are currently evaluating the nPM1300 as a key component on one of our new designs. This design must support both USB and solar charging using relatively low power...
