Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi,
As showed in the code, I masked " else if (m_nw_state.provisioned_devices == 0) ", then it reported "NRF_ERROR_NOT_SUPPORTED".
Can you tell me how should I do...
Hello,
I didn't manage to run PA/LNA switching with softdevice (function: sd_ble_opt_set(BLE_COMMON_OPT_PA_LNA, &options)) with P1.* GPIO pins.
Note that all P0.* pins...
Hi,
Is there any chance that we can completely turn-off the radio part of nRF52832 and only the application part of the processor running. Also, we should be able to turn...
Hi,
I would like to program and debug a code into the Nordic Thingy:52. I read that I should have either J-Link or nRF52 DK. And I have the nRF52 DK, but I don't know...
Hello all,
I'm working with the nRF51 SoCs, with the s130 SoftDevice and SDK12.1.0
I have a BLE Nano from Red Bear Lab that has a nRF51822 doing adv and it expose...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
When initializing a UART instance (0 or 1 or both together), the current consumption increases to 600 μA
Then deinitialized UART, but consumption is not reduced!
- I tried...
Hello everyone!
I've had an ESB application running o the nRF52832 for more than a year. When I moved it onto the nRF52840 it no longer works. There are no changes to the...
Hello,
I'm developing a home automation related product using mesh. For testing mesh functionality I'm placing the DK in different rooms and testing the range. As a power...
I have a small project on a custom board using an nRF51824 processor.
The code basically initializes the BLE stack timer and GPIO and then falls into a loop
while (true...
