Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi, I was using the BLE online power profiler to determine possible power savings with the nRF54L15DK over the nRF52840 using the zephyr bluetooth broadcaster sample. The...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hi, I am using ncs 3.0.2 and an looking at adding extra .conf files during production. For the app it works fine using --extra-conf, but I can't figure out how to add one...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Dear all,
I tried to program and test the iBeacon application on the s110 folder from nordic examples.
The code on the Cortex-M0 has problem. Seems during programming...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
I was wondering whether it is safe to use a delay (such as implemented by nrf_delay_us) to, for example, delay an iteration of a while loop, or that it is always better to...
Dear Sir/Madam,
I am testing iBeacon application on the nRF51822 mounted on nRF6310 motherboard.
I programmed the ble_app_beacon application in the keil_v5\ARM\Device...
Hello,
I get a sample code in the dir flllowed after intsalling nRF51 SDK:
\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon_code\main.c
but I still...
I ve installed CSR bluetooth 4.0 adapter , it can communicated with even the bluetooth 2.0 devices, how ever it even can not discovery the board when I programed the softDevice...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
I have a fully functional code for 8-bit data acquisition using nrf24le1. Now i want to upgrade it to 12-bit resolution ,but i have problems in doing so .
In my project...
I am making a module using nrf51822 and a chip antenna.
I need a layout from nrf51822 to a chip antenna through matching chircuit.
Unfortunately, I don't know how to...
Hi,
1. I want to design a product as a tag,which can read the temperature and transmit the data to a host,the host can read several devices' data. which mode would I use...
Hi everyone,
Just recently I've got two nRF6310 EVB boards with a nRF51822!
When I connect board via USB and open the nRFgo Studio, it can recognize the board as nRF ISP...
For nRF5122 BLEStack, it is analyzed that the event is processed in each of the interrupt handler for the interrupt terminal BLE
I understand that is processed through the...