It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
Hi dear nordic employee:
I use blew：
chip：nrf52832 CIAA-B00
SDK: 12.3.0
what‘s I want is same as this ， when the interrupt happen，I want to know the toggle is HIGH_TO_LOW...
Hi,
I want to develop a 4 Chanel Wireless audio system
I am using an EEPROM (without MC) to configure the nRF24.
I want to split the available band (2,4GHz to 2.5 GHz...
Hi,
I have the problem, that nrf_crypto_init() does not find any backends and thus is skipping the initialization.
What is the precondition for NRF_CRYPTO_BACKEND_SECTION_ITEM_COUNT...
Hello,
after migrating to SDK15 we noticed, that our spi master seems to clock out single bytes instead of a continous clock for the whole transfer.
The Migration guide...
Hi
I want to update bootloader.zip file over BLE DFU mode without signature checking , the open bootloader example only for USB,
How to disable bootloader signature checking...
when message relay by any node how can other node know that it is for him and update status.
for example if I subscribe some nodes to 0xc001 group and others to 0xc002 group...
Hello,
I am making a PCB for my project using the nRF51822 chip? Can I power a LED with the GPIO pin or do I need to connect a MOSFET to drive the current? Also, I want...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
hi,
I'm trying to merge the the proxy server and beaconing example together. When I compare two main.c and copy the advertising part from beaconing to proxy server example...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
Hi Sir
I'd want to send DTM command by hard code, but I don't know where is the command spec for reference ?
Has any one could show me where is the spec ? and give me...
Hi,
I am using nrf52832 with soft device 3. I am operating on peripheral role, while i am initiating sd_ble_gattc_exchange_mtu_request with desired MTU ,it internally sends...
Hi! I am using SDK15.0 and SD 132 v6.0.0. My IDE is Segger Embedded Studio.
Everything was working fine and then suddenly after few weeks of developing a problem appeared...
