Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello all!
I'm trying to optimize power consumption for project based on nRF51802 and external host MCU. My current platform and toolchain:
1. nRF51802 as Bluetooth controller...
Hello, i am using NRF52840 board with NRF52840 SDK version 15.2 with softdevice 140 Version 6.1. I am using the BLE_NUS_UART_C example and id like to send a scan request to...
Dear nordic,
BLE advertising happens in 3 channel(37,38,39) and scanner scans these channel based on scan interval consecutively
I want to scan single channel instead...
Using nRF Connect for both iOS and Android, the advertised name is the same for both apps, i.e, DeviceX.
Clicking on the device information also shows the Complete Local...
Hello,
I am using an nRF52840PDK (master) to use an SPI peripheral, where my code is based on examples\peripheral\spi. My IDE is Segger Embedded Studio and I am using SDK...
Hi Nordic Team!
Please find below attached the schematic for my custom nRF52832 proto board. The boards are already manufactured and are in the bringing-up stage. The designs...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
Hello Everyone ,
By using sdk version 15 for NRF52840 I wish to connect the lsm9ds1 sensor to it and using seggar embedded studios IDE. The header files available in google...
Hello, what is the best way to provide optional enable or disable option for a user in terms of keeping BLE module powered on or off. I am thinking of 2 options , can you...
Hi everyone,
I'm currently working on a nrf52832 board and i got an issue on Gpio config after a reset.
I configure a gpio with a register value of 4, low level, output...
Hello. I am reading this manual infocenter.nordicsemi.com/index.jsp and trying to compile but there is an error durring linkage phase, Linkage nrf_init: undefined symbol ble_conn_params_init...
Hello Nordic team,
I already managed to get into DFU bootloader using buttonless DFU service, and successfully triggered application uploading process, but the system randomly...
Hello, To use the nRFMesh app which Project needs to be flashed to the Nrf Board ( I have nrf5832) . I see there are following workspaces : (1) nrf5_SDK_for_Mesh_v2.1.1_src...
