Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I have an nRF52840 based custom board (myboard, NCS2.70)
its partitions node closely follows the nRF52840DK dts file:
both have &flash0 in the /chosen group...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
As you can see in the schematic, I have a custom board, and I’m uploading code to it via J-Link. I can control the pins, turn on an LED, and read a button without any problems...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...
