Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
Build configuration is: SDK: nRF Connect SDK v3.0.0 Toolchain: nRF Connect SDK Toolchain v3.0.1 Board target: nrf52833dk/nrf52833
All other values left at defaults.
There...
I had like three Thingy52s for a project and have just come back to it after about a year.
The batteries are now dead and the device does NOT seem to want to charge.
All...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I am trying to use the HCI UART application with channel sounding enabled and communicating with an external host. I was able to perform all CS procedures, and when it was...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
