Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
Hello,
I am trying to play the AT45 DataFlash driver by directly copying the sample code from nRF connect SDK v2.9.1 (C:\ncs\v2.9.1\zephyr\samples\drivers\spi_flash_at45...
Hello,
i have one PPK2. Recently i find the current reading from PPK2 is relatively large compared with actual current value.
For example, actual current value vs PPK2...
I am currently working on creating a custom PCB which features an nRF9151 module. I am currently working on pin assignment for our peripherals. Given Zephyr uses a device...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
In NRF5 SDK17.1, I disabled the Bluetooth broadcast channels 38 and 39 by configuring channel_mask. However, when I measured the broadcast current waveform, I found that there...
I'm working on a IoT device that leverages the AWS IoT and AWS FOTA components from the nRF Connect SDK. The device is battery powered, and so I want to limit the connection...
Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Hi all,
lesson2, excercise2 is missing the code snippits.
Excercise1 and excercise3 do have code snippits to copy.
I tried on both Chrome as on Edge, but the snippits...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
Hi,
I have successfully updated the firmware on the nRF5340DK controller using the DFU MCUBoot method. Now, I need to add Secure Boot NSIB to the bootloader and integrate...
I'm using ncs 2.9.0.
1. I flashed the firmware V0.15.1 on the device. And .
2. Update it "Confirm only" with nRF Connect Device Manager App to V0.15.2The update was Compelete...
I've recently encountered a problem where the Device Tree Visual Editor no longer displays any peripherals (ADC, UART, SPI), making them uneditable. I have had my own board...
Hello,
We use nrf54l15dk + MX25R8035F external flash to do the matter development on NCS2.9.0, and we meet some problems:
1. when the matter.ota is 1003KB, takes about...
