void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
We have enabled the watchdog feature in our application running on the nRF5340 and nRF7002. In rare cases, we’ve observed that the nRF5340 hangs during zephyr library...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
Hello!
We have a project where we are using the nRF52840 with the ADS7052 (an ADC) on the SPI bus. We are using Zephyr 4.1.0, but I guess its same same with nRF Connect...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Somehow a program I have running on a nrf52840-DK board will enable protection. This kind of screws up the small application I am testing because it seems to lock out the...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hello,
I am developing a board with the SIP nRF9151.
I'm designing the board with a shared antenna for both the GNSS and LTE signals (Ignion NN02-224).
For the antenna...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
