Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
On a new board based on nRF9160 I am having trouble figuring out how to bring up the board.
I am using Azure IoT hub and can successfully build an application that can connect...
Hello,
I want to use the bq274xx.c sensor library. The bq274xx battery fuel gauge has an interrupt pin, which would allow to have the CPU idle until something interesting...
Hi there,
I'm using a slightly modified version of coap_client to test out network connectivity with a 1nce SIM card (USA). Essentially, I've modified it from a GET request...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi there everyone I am new in nRF development. I was recently trying to add conexio stratus pro but i could not find it in my VS extension. What could be the issue?
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi,
I really like the new Zephyr conn_mgr, it is really easy to use, almost UNIX like. I am wondering what is now the best way to control PSM. Will CONFIG_LTE_LINK_CONTROL...
I have a timer int callback like this:
void pwm_all_handler ( nrf_timer_event_t event_type , void * p_context )
{
if ( event_type == NRF_TIMER_EVENT_COMPARE0) {
...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hello everyone!
I have a question about flashing firmware to a PCBA with the nRF54 and nRF91, or any dual MCU board in general.
When looking at the Thingy91(x) this...
Hi everyone,
I have a custom board using the NRF9161. Its hardware is loosely based on the design of the Conexio Stratus Pro and I’m using the Stratus board definitions...
