Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
We are evaluating LairdTech BL654 module for our BLE application. We are able to use NRF 15.2 SDK to setup BLE based connection and data transfer.
We are sending around...
Hello I'm using the official example and BLED112 dongle with the demo from C:/Bluegiga/ble-1.60-140/src/thermometer-demo (main.c in attachment). The problem is that device...
I'm using SDKv15.2.0
I think there is a problem in nrf_dfu_app_is_valid() in components/libraries/bootloader/dfu/nrf_dfu_utils.c
If the CRC check fails, the return value...
Hi,
What is the timing of the indication retry mechanism (SDK14.2, nRF52832) ?
App use sd_ble_gatts_hvx() to schedule message for sending
At the next connection interval...
Hi, Great Nordic Support teams:
I'm wondering if the only limitation of the choice of L3 on nrf52832 layout is just the tolerance under 10%?
Cause it seems to be the...
Hi,
I've recently enabled the watchdog in our project which included buttonless DFU. Project is based on FreeRTOS, SDK14.0, S132 v5.0.0 on custom board nRF52.
Since the...
Hi All,
I'm running a windows box with Android studio with the GitHub Thingy Repo https://github.com/NordicSemiconductor/Android-Nordic-Thingy project downloaded. The project...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about SPIS and SPIS event "NRF_DRV_SPIS_XFER_DONE".
1. What would trigger event...
HI,
In need to generate a sweeping tone to drive a piezzo element, i determined the tone should be sweeping back and forth between 2.5KHz and 4.5KHZ at an approximative...
My ultimate issue is trying to get a bootloader working on custom hardware with an nRF52832. The bootloader is mostly the base UART DFU bootloader from the Nordic SDK, with...
Hi,
I'm able to run the DFU mesh from the quick guide and now I want to integrate the DFU into my application.
My application is based on the light switch example, so...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...