I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hello,
I am designing a circuit using the nRF81522 chip.
I was wondering what should I do with the unused I/O pins.
Would it be OK to leave them unconnected, or there...
Hi
Could I use 3.3V to the C3 capacity in the application example,datasheet?That is to say,C3 doesn't connect to VDDPA pin and 3.3V connect to the C3.I found that it is...
We have developed our custom nRF8001 board and connected with Arduino UNO bord. we have used nRF HRM demo application from Github . We are using nRF utility application from...
OK, I didn't read enough fine print before I plunged in, but my version of the nrf51822 I have on a bunch of boards isn't supported by the new SDK.
In a premature onset...
I'm trying to use notifications with Android 4.4. When my service issues a call to sd_ble_gatts_hvx, the result is BLE_ERROR_GATTS_SYS_ATTR_MISSING.
From this link , I...
Hi
when i call twi_master_transfer function in for(;;) loop of file ble_app_hrs project.
Kindly tell me what to do for that.
for (;;)
{
for(i=0;i<10;i++)
{
...
When I plug the PCA10000 into my mac I can see it presents 3 USB interfaces. The first is interface class 0x02, Communication Control, the second is 0x0a, which is Communication...
Hello
I have problem to reach 100 feet and a high data rate using BLE.
I am thinking about using gazell. Is possible to communicate with gaxell protocol to IOS and Android...
Hi guys,
I am trying to get the maximum packet size out of my nrf24 radios. If I am implemeting my own radio protocol which doesnt require 3-5 bytes of address is it possible...
Note that nWP-018 "Migrating to the latest nRF51822 chip version" specifies that the SDK version which should be used with the Eval Kits I have (version 1.0, chip variant...
I'm using the nRF51822 with the version v5.2.1 S110 soft device and have implemented a communication scheme that is very nearly identical to the Nordic UART protocol as implemented...
Hi,
I'm currently working on an Android 4.3 app who must communicate with a model of a specific device.
This device contains a Bluetooth low energy chip nrf8001 and there...
Hi,
I have a problem when running 51822 with Nrf toolbox on android 4.3 Samsung S4. The problem is that the BluetoothGattServer disconnect itself after 30 seconds. The...
