We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hello,
For a month I have been trying to find a solution to update my devices which are at my customers (these devices have a bootloader, softdevice and app coming from...
Hi
ncs 2.6.1 / toolchain 2.7.0
we have developed a Product using ANNA-B402 (with nRF52833).
Now we made a product variant with nRF52833 WLCSP. Both use the same application...
Hi,
I face a 3mA consumption while I have CONFIG_PM=y and wether or not I have CONFIG_PM_DEVICE=y.
The idle thread is reached and executed :
And the idle thread...
Hi,
Is there a way to make the main thread to execute after any interrupt?
For now, I have something like this (ncs 2.7.0):
in main thread :
In each IRQ handlers...
Hi,
I am sending 20 bytes of data in a beacon format. These are fit into m_beacon_info[2] to m_beacon_info[21] defined in ble_app_uart code from nordic SDK:
I send beacon...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hello All,
I wanted to sniff ZigBee Packets using Wireshark SW, I am following the below link for the setup,
https://docs.nordicsemi.com/bundle/ug_sniffer_802154/page...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. We have a project using the nrf52840, which is sometimes used by carriers. I ported radio_test to...
Hi
I am using HCI Power Control sample to dynamically control TX power. I found that the TX side's connection RSSI and RX side's are diferent, at some point it even has...
Hello, I'm trying to follow this example (Serial DFU) , on a nRF52840 custom board, but I'm getting the following error:
I couldn't find any relevant information and also...
Hi,
I have recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. To begin, I used the "Hello World" sample code. While I was able to successfully build...
I have searched everywhere and can't find a working example that shows how to create a new BLE ID and save it to the setting s partition.
Please show me the configurations...
I am incorporating the nrf52840 into a new design and it is my first time working with a Nordic product. I am looking to start with the SEGGER J-LINK EDU MINI due to it's...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi,
I am debugging the zigbee functionality and would like to enable the zigbee log,already enabled log in prj.conf but no data coming out.What do I have to do to enable...
