Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
Developing with S112 + Emulated NRF52810 I've run into a road block.
I've set `m_adv_uuids` to the following:
static ble_uuid_t m_adv_uuids[] = { {BLE_UUID_DEVICE_INFORMATION_SERVICE...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52.
I am using MPU9250 and nrf52840 pdk.
I've managed to set up the DMP and...
Hello - I have looked through documentation and can't confirm which component on the board is the BLE Module. Could someone follow up with an image of the board to help confirm...
Hi, we are looking at using a FCC pre-certified nRF52832 module such as the murata MBN52832. It would be for a wrist mounted product so will be in close proximity to the body...
Hi there Nordic Semi/ forum,
This is actually my first post here.
I got the NRF52 DK and I want to implement the NFC type 2 ( passive) tag with it that I could both read...
Hi, I am trying to use P0.9(nfc pin) as gpio(input) to read the charging status of a battery from battery charger IC(BQ 24230). the Open-Drain Charging Status Indication of...
hi Nordic engineer
hard platform : N53832DK, 51822DK
software platform nRF52832 use SDK_14.2.0, nRF51822 use SDK 12.3.0
nRF52832 as ecntral and peripheral; nRF51822...
Greetings,
in the system I develop I shall have a task resposible for fetching some amount of data from Flash to RAM. I should mention that the code will be executed from...
Hi,
I try to activate the bonding with the "ble_app_multiperipheral" exemple project I have modified.
It is very strange because I can bond as wanted but only if I set...
Hi all,
I am having query regarding BLE Security.
Which options are provided by BLE for security.
Can anyone provide option in below category?
1. Security in Connection...
Hi all,
Going through the sniffer document and devzone tickets, I observe that there is no official nRF sniffer software to emulate nRF52840 QIAACA SoC as BLE sniffer. ...
Hi Everyone
I was trying to use segger embedded studio for nrf52840 PDK.
I could get the example codes working but when i tried to create a new project and try to include...
Hello, I am trying to initialize the service Power Cycling from the files of this link https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
I get...
Hi,
I've been trying to use the nordic power profiler v1.1 with my nRF52 development board to figure out how much current is consumed during operation.
I used the power...
