Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I am using custom board with nRF52832 and Keil uVision5 as IDE. I started with simple example which is just to ON the LEDs.
Code(all necessary header files are...
Hi,
I'm developing a FW that is now validated. We are "almost ready" to go in mass production (6000 PCE for the first batch).
For the moment, I'm still using the debugger...
Hello,
I am using the mesh pb_remote example in order to have a multihop scenario. I would like to do some latency calculations, so some kind of bidirectional communication...
Dear all,
I'm using NRF52832 with SDK 14.2.0 and SD 132 v5.0.0.
I have my own implemented application working properly when is flashed directly without bootloader, only...
Hi,
I'm wondering if anybody has performed a test of, or has experience with Nordic Semiconductor thread mesh stack (nRF5 SDK for Thread and Zigbee v1.0.0) in a large scale...
Hi, i used the 'nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch' i have two question:
1: How to added more Client in one mesh net?
2: How to configuare node to 'low...
I am trying to make RF USB dongle using nrf52840.
Before the PCB production, we are using DK to test, but the firmware is not uploaded because VDDH and VBUS of DK are connected...
Hello Nordic!
Sometimes we have a problem with a services discovery. We have no custom services. Only DIS, BAS, NUS and DFU. (nRF52832 and SDK15)
This problem is currently...
Hi,
I'm working with the light_switch example on Mesh 2.0.1 and I would like to modify the simple_on_off_client_set_unreliable function to broadcast to all servers in the...
I am evaluating TAIYO YUDEN board EKSHSNZWZ.
I've flashed s132_nrf52_5.0.0_softdevice.hex using nRFgo Studio.
I use Keil uVision to test "nRF5_SDK_15.0.0_a53641a\examples...
Hi. I am trying to transmit a microphone signal to the nrf52832 DK board.
Before development, i checked it by connecting a microphone(ADC) and a speaker(PWM) to one...
It wasn't until I downloaded nRF-Sniffer-v2 that I discover the release note below that explicitly states that nrf_sniffer now supports all platforms supported by Wireshark...
Hi,
We want that any bulb or any devices (Server device) of BLE 4.2 should be able to work with BLE Mesh SDK(Client). We are using the nrf52832 with SDK BLE_2.0.1 for the...
I would like to sample a digital IO input from two IO's into the processor internal memory incrementally per every rising or falling edge of each of the signals.
Is there...
