We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Dear Sir.
I have a question for app timer in nRF52 DK(pca10040).
I was called a example source(ble_app_hts) for nRF5_SDK_11.0.0-2.alpha.
And I add UART part for logview...
Dear All,
I have question regarding advertising in NRF51. I measured the power that be used when advertising using osciloscope and set the advertising interval of NRF51...
I'm having this event and I'm not sure what are the conditions required to trigger it, also what does it mean exactly since the documentation does not say more than a line...
I had attended the Nordic 2015 Tech tour in Helsinki and it was very nice of Nordic to give away nRF52 DK to all attendees. So far, I've been busy working with nrf51 but today...
I follow this instruction to turn Raspberry Pi into an IPV6 router on IPV4. My raspberry pi works well after I add nameserver to /etc/resolv.conf.
But other device in my...
I am experiencing an error that I can't figure it out why it is happening and where to go and try to fix it.
I am using the subscriber implementation on my nRF51, Raspberry...
I see in multiple examples of NRF51 SDK:
#define APP_TIMER_MAX_TIMERS (2+BSP_APP_TIMERS_NUMBER) /**< Maximum number of timers used by the application. */
but it is...
In ble_gatts.h, I see:
#define BLE_GATTS_FIX_ATTR_LEN_MAX (510) //< Maximum length for fixed length Attribute Values.
#define BLE_GATTS_VAR_ATTR_LEN_MAX (512) //< Maximum...
Hello Everyone,
I have been working on the NRF51DK by using proxmity examples as reference when i added the static passkey for the connection security it is working well...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels? is it possible to achieve on nrf52 DK.
1>How to set up...
when i turn on the Keil, they have showed error to me
"Install missing Software Packs?
NordicSemiconductor.nRF_ConfidentialDeviceFamilyPack"
then i try to re-intall familypack...
Hi,
I wanted to know How can I find if any application on any platform(Central device)is listening to my advertising packet or not !!
The whole idea behind this is to...
Hi,
I have made a few custom boards based on the nrf51822 but on my latest design, I'm having a new problem that I haven't seen before. I have read the posts in the forums...
hi everyone,
i'm testing an application on pca10036 board where i need to create a large buffer. i use Keil v5 as dev. environment. My buffer is static and global, therefore...
