This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I followed test steps mentioned in dfu_quick_start.md file to perform DFU over mesh.
1. Below is the error i am getting while creating DFU package, Please help on this....
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
I am trying to erase page from RAM using "nrf_nvmc_page_erase...
I have a situation with the devices my company builds. From what I understand, they've been designed with a small flaw, which causes them to sometimes get stuck and require...
51822 problem: the device unexpectedly restarted, the current of the device becomes more than 800 ua, and the same as the jlink download current; the software reset current...
Hi
I have been trying the various examples from the SDK with Keil V5.23. Some work, some require changes to IROM1 and IRAM1 before they will run Initially giving an error...
I am trying to change the mac address of my device every time I advertise a packet. I have a callback on_ble_radio_active_evt where I update the address like this:
...
(I'm developing a firmware on nRF52832, but had actually stareted on nRF51822 and observed the same issue, SDK 12, pending migration to SDK 15)
When my app starts, I output...
Hi all,
I am investigating different protocols to support a network of very low-power Devices and Hosts. The Devices are mostly static (i.e. they don't move around very...
Dear developers,
I am developing a scheme where the nRF51 (central role) connects to iOS device (peripheral roles). The nRF51 connects, performs the discovery procedure and...
Hi,
I developed an application on the nRF51 Dongle (PCA10031) and am now trying to port it to this module. It is a nRF51822 AA device (256K Flash, 16K RAM), and it is Rev...
Hello everyone, I'm currently working on a project and I'm encountering issues.
The project involves with a BLE and a smartphone. The goal is to send Data from an application...
Hi
I have successfully(?) altered my application from using BLE_GAP_PHY_1MBPS to BLE_GAP_PHY_CODED. But how can I test it?
Prior to the modifications I tested the application...
Hello.
I'm trying to add encryption to the secure DFU bootloader. I'm using SDK v15. I know this topic has been discussed on this forum before. In particular I have found...
On NRF52840 DK, I don't have a softdevice installed. I want to do DFU with s140 softdevice only update. But it gives the following error:
raise NordicSemiException('Extended...
