After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hi Sir,
In this project, we design w/ nRF51802-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028).
We can test...
Apologies if this is a duplicate post:
I am successfully making nRF example apps in nRF5_SDK_12.3.0_d7731ad using GNU Tools Arm Embedded version 7 2018-q2-update in Windows...
Hi,
I want to use both UART0 and UART1 at the same time, and run the testing example from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in...
Hello,
Using two nrf52 Dev Kit boards for Central / Peripheral. Using Softdevice S132, , peer manager and Segger on Win7.
I have modified ble_uart_and ble_uart_c using...
Hi,
I have downloaded the nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac and try to compile the zigbee_light_switch_pca10056 example under segger embedded studio and I have...
We are developing a standalone application. The bulk power is provided by LiPo battery, which can vary from 4.2V to 3.0V as the battery discharges. I have the system connected...
I recently added bonding and authentication to my application. I have two characteristics with CCCDs and they are both broken. One characteristic is "protected" (requires...
Is there a standard/spec for the UUID used for provisionee devices?
I don't see anything in the mesh examples that indicates a standard UUID format is used.
It allows...
I am using an nRF52 DK with Soft Device 6.1.0 on a Windows platform.
I am trying to add a new BLE Service and calling function sd_ble_uuid_vs_add() but get NO_MEM error...
I am developing three different projects for the nRF51822 using SDK 12.3 and the app_uart_fifo code module. Details of the projects are as follows:
Project 1 - implemented...
I am attempting to run the mesh Light Switch example with a provisioner, client and a server in debug mode using the Segger SES. I am attempting to debug the server code on...
Hello everyone, the sdk version that I use is 15.0.
I'm trying to connect my nRF52832 (master) to an external SPI slave memory (N25Q) to write and read data. The problem...
Hi Everyone,
RFX2411N is used to extend signal coverage of NRF51822. Here are the configuration below:
Use radio notification to generate an interrupt
Use this interrupt...
Sir,
System notifications where enabled On my mobile but still I did not get any kind of notification from Eddyston Beacon-URL.I am using nRF52840. Is there anything such...
