Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Hi,
We are currently developing an application where we use a nrf52811. Currently i am working on integrating the BLE-Stack as this is the last part missing.
I am constantly...
Hello -
I am working through the DevAcademy - nRF Connect SDK Intermediate lessons. I have reached Lesson 7 Exercise 1, found here - https://academy.nordicsemi.com/courses...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external QSPI EEPROM used ( MP95P08...
Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild.
I want to be able...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
Hi guys,
Maybe someone already did this work but if no:
I would like to take only the relevant parts to my project.
I am not sure what can be given up.
I need cellular...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
Hello,
Im trying to flash RAYTAC AN54L15Q-DB board but im keep getting following error:
Error: One or more batch tasks failed: * 1050050051: [Probe] Emulator error: Failed...
Hi,
We are doing RF Test for nRF52840DK, and we are using CBT Bluetooth tester. Commands are going to CBT fro nRF board.
My Question is code we need to flash for RF test...
