Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I am using sdk 14.2.0.
nrf_gpio_pin_set(OUTPUT_PIN); this function sets the gpio pin to vdd.
nrf_gpio_pin_clear(OUTPUT_PIN); this function set the gpio pin to ground...
Hello,
I am using a nRF52840 with SDK 14.2 and I am trying to synchronize my "app timer" which uses the RTC1 with respect to an external client which is connected over TCP...
I downloaded the latest SDK(15.1), and how to advertising more infomation,more than 31 byte.
init.config.ble_adv_extended_enabled = true;
0> <error> app: ERROR 7...
Hey guys,
I am using NRF51DK board and SDK v12. I want to add MPU6050 library to fatfs example but I have some problems. When i add "mpu6050.h" to my project i get "Not...
Hi,
I'm using NUS service on nRF51822 with SDK 12.3 .
I want to secure the communication between the nRF and the mobile application.
So, I want to know the different...
NRF51822
SDK12.3
keyboard demo code
After each delete match at the PC end，None of the broadcasts are searchable。Then I Google the content like this。
I wonder...
Hello,
I am using NRF52840 in my System. We like the USB access on NRF52840 and would like to use it. However, I don't need BLE in my application. Can I leave the Radio...
Dear All,
i want to make a product which using nrf24le1 chip, but now i'm stuck on the antenna impedance matching issue.
i'm not very familiar with the antenna design...
I'm try to using Nordic 52832 board to send hexadecimal to the phone, but it still receive for ascii.
Using example\ble_peripheral\ble_app_uart code for sending.
Hello
We have a project of energy meters with mesh network.
There are some parameters important for us:
Time of reconfiguration
size of network
connection range...
When I plug the kit into a USB slot on my computer, the nRF52 DK does not appeared as a removable drive named "JLINK" as it should according to the documentation. Has anybody...
I m working on SDK-11, and using sample program experimental_ble_app_blinky, in this code I want to read RSSI value and want to show on NRF Connect app. But its not showing...
Hello,
We are using nRF52832 DK, nRF52 sdk15.0 with SES IDE in windows 10. Currently we have senor network which is trigger every 1 Hr and send data trigger time set in...
The hardware is a custom board with a Rigado BMD300 module (which uses the nRF52832). I am using Softdevice S132.
My code base started as the ble_app_uart peripheral example...
