Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
We have a project that includes a custom board definition and out of tree driver with folder structure as follows:
Our project builds successfully with SDK v2.7.0...
Hello, please help. I want to use nrf54L15 to connect to Bluetooth devices (Bluetooth headsets or other Bluetooth devices) and test the throughput between them. Is there any...
I have built and flashed the openthread/coprocessor sample using VS Code specifying "nrf54l15dk/nrf54l15/cpuapp".
I then tried to run it (on Ubuntu 24.04.2 LTS, x86_64)...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Hi Team,
I am setting up an OpenThread Radio Co-Processor (RCP) using the nRF5340dk. However, I could only find examples for the nRF52840 and other chipsets but not for...
Hi
I am working with a custom board with nrf52832 with only 32Mhz external crystal. My application is working in the nrf52832 development kit but when I use the custom board...
Hi
Is it possible to stream 128 kbps .acc, .lc3 or .mp3 Spotify audio from server to nrf9151 ?
It says it supports 300 kbps download, so maybe 150 kbps is realistic ?...
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Currently using NCS v2.9.1 nrf54l15/cpuapp custom board derived from nrf54l15dk, customization to de added after solving the issue below.
The project is successfully compiled...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
