Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
Hi,
I would like to synchronize 2 Sensors with one dongle. So the problem is that we have two sensors and we want to start the measurement at the more or less (1 ms) exact...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
Hi,
I want to use nRF52832(PCA10040 board) to communicate with nRF24L01+. I program the example application( \examples\proprietary_rf\esb_ptx)(SDK v15.0.0) on the board...
Hello. I'm developing an application with a custom bootloader and I'm using "settings" data structure placed in FLASH. Because we can erase only full pages, the first page...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hi,
I try to program hex file with openOCD. The flash part is written without any problem. OpenOcd only fail to write the UICR registers beyond 0x10001200.
However it...
Hello,
Which one of the following statements regarding " sd_ble_gap_connect " function call is true:
(1) Can sd_ble_gap_connect function put the central device into initiating...
static void pdm_event_handler(nrf_drv_pdm_evt_t const * const evt) { /* Process the events. */ }
/* ... */
/* Process the events. */
Can you make a little more detail...
Hello,
I have NRF5230 DK board and I have powered the board with external battery. Solder bridge SB12 is shorted and I have cut the jumper SB29 and disabled power for Interface...
I am trying to connect nrf52832 ble module to esp32/esp8266 application mcu connected with SPI interface.
I use ble_central/ble_app_hrs_c application, but found that the...
Hi Sir,
we use 52832 ESB , one PTX and two PRX. (PRX_A and PRX_B)
A and B have same base_addr_0 and base_addr_1 .
diffrent addr_prefix
PTX send package to A and wait...
