Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
hi :
i send characters of SPI master of 52DK to SPI slave of our target board(Nordic nRF52832), our target board use SDK v12 spis example. but spi slave event can not rececive...
I am using SDK 12.3.0 and S130 2.0.1.
In example ble_app_uart and ble_app_uart_c,
Central setting:
Peripheral setting:
Why it took so long to discover service...
Using the same connectivity firmware, a dfu update using nrfutil takes about four times as long as the same update using nrf connect. I have to setup dfu updating in a production...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
Hi,
I am trying to use Segger embedded studio for my project,
I get these errors:
Building ‘ble_app_uart_c_pca10028_s130’ from solution ‘ble_app_uart_c_pca10028_s130...
hello,BPROT does not work normally when i am debugging BPROT.
when i set CONFIG0 bit2 to 1,that is NRF_BPROT->CONFIG0 = 0x00000004,then i want to erase block 2(start address...
I am having a hard time turning ON semihosting. Here's my setup:
- Debugging is done via Eclipse GDB SEGGER J-Link Debugging with the Enable Semihosting checked and console...
Hi all,
I have a problem. I add NUS to light switch proxy . But the first time, I use nRF_UART or nRF Mesh connect to my Dev Kit. Then, I disconnect , I see it run MESH_GATT_EVT_TYPE_DISCONNECTED...
Hi,
I'm trying to set up a custom project with all the mentioned components. I build the bootloader, I'm using the `s140_nrf52_6.0.0_softdevice.hex` for the softdevice and...
Hi,
When i tried the light switch example from the Mesh 2.0 source code, i got the error code NRF_FAULT_ID_SD_ASSERT. when it is doing the provision process.
The last...
hi Nordic Support Team,
One Of Client has a Machine with Bluetooth Sending some Data every 1min.
They want to capture this data and Send this data through Mesh. Is it...
Hello,
I am using sdk 12.2.2 and nrf52 customised development board. My challenge is as follows.
1) I am getting success in fds'_write function.
ret_code_t ret = fds_record_write...
We planing to use the NFR52832 with heavy algorithm (Real time ECG analysis) with light BLE use. Does the BLE have higher priority that can slows the algorithm?
I have a wireless project. Requirements as:
Support platforms: Desktop/Laptop and mobile, Pc/Mac/IOS/Android. etc.
many connections: flexible but can support 100+...
