Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I'm testing External interrupt.
Current concumption was just 50uA around(low speed advertising mode).
But It goes 1mA around...
Hello
I'm working on a network of nodes with more than 300 nodes
each node is constructed by (1 arduino nano,humidity sensor, 1 relay and NRF24L01 +)
I'm working with the...
Hello. I'm trying to understand twi_sensor sample code on nRF51. (nRF51_SDK_10.0.0_dc26b5e\examples\peripheral\twi_sensor)
I have a trouble finding where the function twi_handler...
Hey,
i've bought the nrf52832 Preview DK some time ago, are there any big changes to the new DK? So if i buy a new nrf52832 IC i can desolder the old IC and use the new...
If I have some value and this value has become out of desired range I want to change property from indicate to notify.
I only found function sd_ble_gatts_characteristic_add...
I'm developing an application for a device which needs to support both DFU and some method of restricting connections to a single central (ie: bonding). This is a challenge...
Hello!
Is there have any tutorial for how to create GATT service on the MCP(master control panel app) and what coding do we need to add to the project?
Hi, I would like to put a nrf51822 device into system off mode and wake it up with a GPIO transition from high to low.
I would like to measure the press time of the button...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
Hi,
I am upgrading to SDK 11.0.0 and S130 v2.0.0 from SDK 9.0.0 and S130 1.0.0 and I am stuck with an error when I call sd_ble_gap_adv_start. Here's the code that now fails...
I have the following two lines with pin 21 not connected to anything:
nrf_gpio_cfg_input(21, NRF_GPIO_PIN_PULLUP);
uint32_t value = nrf_gpio_pin_read(21);
I would...
Hello!
I'm trying to flash my SeeedStudio Tiny BLE board (nRF51822 QFAA) with SoftDevice S110 using Keil but it doesn't look like it's going to let me. I'm just getting...
