Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
We are using nrf51422 in our project.So right now i am loading the program using the Usb cable .Here my doubt is can we able to flash the program by using usb to uart...
Hello. It is almost the same as the question ( devzone.nordicsemi.com/.../set-data-type-for-notify) given three days ago. I want to “Notify” new data in the “rscs” project...
does FDS have append data functions? I want to receive big files(>500KB) from BLE,but I can put it into RAM buffer, so can I create a file in FDS and append it from BLE directly...
Hello Recently I have been working on a project for a 52832+ three-axis accelerometer. I have encountered some problems. SDK15.2 IIC 1.started a timer and it was time to collect...
Hi all,
I’m currently working with the nrf9160 sip on a bare metal firmware project. I know the official support path is only with Zephyr OS but I’m facing an issue I’m...
I modified my nRF52840 dongle as is was described here Does anybody have a single diagram showing how to connect the DK's P20 pinout to the dongle ? Thanks,
Matthew
Hello! On 2019-06-24 the following mail was received:
Product update notification June 24, 2019
Hi Bojan,
We've just released a new version of our SoftDevices, version...
To the kind attention of Nordic support team,
Could you please give a very quick look at those attached gerber files? Do you think there is something that is better to correct...
Hi Nordic team support,
I want to test communication range between nRF528xx device that support LE coded with samsung galaxy s10 (support LE coded also)
1. If I configure...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...
Hi,
What's the easiest way to subscribe to the MQTT messages that the thingy91 sends to the nRF cloud?
I have tried setting it up with a node-red and a python client...
