after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Is it possible to generate a zip package containing both firmware and softdevice in such way that the soft device will be updated only if the current device softdevice version...
I have some module chip connected to the nRF9160 DK providing the sensor data over I2C line. In some state transition of the module the short reset pulse needs to be generated...
Hello, I am using BLE secure bootloader example on nRF52840 with SDK 15.3 and softdevice 61.1. I can see the bootloader protects the MBR page and Bootloader space using ACL...
When I run "AT+COPS=?" WITHOUT a SIM the modem always responds properly.
When I run "AT+COPS=?" WITH a SIM the modem does not respond as expected. I get error after approx...
Hello everybody.
I have been working on nRF52840 for a time. I am trying to flash the chip with ble_app_uart_c (SDK 15.3.0). I have applied everything essential, but my...
Good morning everyone,
I am facing an apparently common problem (reported with some variations Here , Here or here ) which is driving me crazy. In the linked discussions...
I am using function "modem_info_json_object_encode" to encode modem info into JSON to send upstream.
I get the very strange format where you encode dictionary as string...
I am curious to know do we have any practical BLE based products such as Fitbit or heart rate monitor, in which there are different type of messages are sent from one end...
nrf_crypto_svc.c throws a bunch of errors during compilation. The errors have to do with SVC_REGISTER_FUNCTION. Example error message: function 'SVC_REGISTER_FUNCTION' is...
Dear ,
I just want to know about thingy 91 - pca20035 status
1. asset_tracker :nrf9160 SIP works
2. usb / usb_uart_bridge / : nrf52 ?? confusing !
and how about...
Hello Support Team,
Currently NRF52832 is being used for wearable product ,
For NFC Card Emulation Mode whether NFC Front END IC is required ?
or Can go ahead directly...
I designed a prototype using nRF52832 controller. On this prototype I was using the same Flash Controller ATSAM3U2 used on the nRF52DK.
I am bringing up the prototype and...
Hi,
From time to time, we need to send data directly to certain node. There is AF_DataRequest() API in CC2530 to do that. Is there any similar way to implement that kind...
Hi all,
My aim is to " read Four ADC Channels data and sent them to nRF Connect bluetooth app".
For doing this i used "saadc " and " ble_app_uart" examples.
Till now...
