nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
i'm testing an application on nRF52, with nRF5_SDK_11.0.0-2.alpha and SoftDevice 132.
I took the ble_uart example and added a custom service with some characteristics...
Hello,
i'm trying a bluetooth connection between nrf UART v2.0 installed on my phone(android 4.4) and nRF 8001 (i'm usign nRF2740 card). My microcontroller is a STM32....
Hi.
I made my own board using nRF51822AC.
I want to connect this board to PCA10028.
There is Debug OUT port(P19).
Net names are EXT_VTG, EXT_GND_DETECT, EXT_SWDIO, EXT_SWDCLK...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
Example code is using "ble_db_discovery_start()" function to discover peripheral.
In this function, there is "SRV_DISC_START_HANDLE...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I'm testing External interrupt.
Current concumption was just 50uA around(low speed advertising mode).
But It goes 1mA around...
Hello
I'm working on a network of nodes with more than 300 nodes
each node is constructed by (1 arduino nano,humidity sensor, 1 relay and NRF24L01 +)
I'm working with the...
Hello. I'm trying to understand twi_sensor sample code on nRF51. (nRF51_SDK_10.0.0_dc26b5e\examples\peripheral\twi_sensor)
I have a trouble finding where the function twi_handler...
Hey,
i've bought the nrf52832 Preview DK some time ago, are there any big changes to the new DK? So if i buy a new nrf52832 IC i can desolder the old IC and use the new...
If I have some value and this value has become out of desired range I want to change property from indicate to notify.
I only found function sd_ble_gatts_characteristic_add...
I'm developing an application for a device which needs to support both DFU and some method of restricting connections to a single central (ie: bonding). This is a challenge...
Hello!
Is there have any tutorial for how to create GATT service on the MCP(master control panel app) and what coding do we need to add to the project?
Hi, I would like to put a nrf51822 device into system off mode and wake it up with a GPIO transition from high to low.
I would like to measure the press time of the button...
I'm using JLinkExe ( J link commander ) for Linux to flash the application firmware on NRF51822_QF_AA target. The following have worked so far, but I'd like to confirm and...
