I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi all,
I would like to setup a system where a single central BLE device (a smartphone) has to talk sequentially to several BLE perihperals (Nordic chips).
I need to...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I made timer(repeated) as below.
void init_timer(void)
{
uint32_t err_code;
err_code = app_timer_create(&m_timer_id,
APP_TIMER_MODE_REPEATED...
Hi,
I have a nrf51-DK, and I use softdevice s130_1.0.0 with keil c 5.18a,
My project with custom service uuid "DFU" and custom uuid "my_uuid", and battery uuid, alert...
Hi,
I've noticed that in the examples that come with nRF5 SDK11 there is a template for creating BLE peripherals (ble_app_template). I was wondering if a similar example...
Hi.
I'm using PCA10028, SDK10.0.0, S130 as central.
After connection, if i want to change SUPERVISION_TIMEOUT, is it possible?
If it is, how can i do that?
I need...
Hi.
I am trying to get the RTC started, and I've followed the rtc example in the NRF51_SDK.
But things go wrong when I call:
ret_code_t err_code = nrf_drv_clock_init...
Hello , RX: nrf24LU Tx: nrf51822 use ESB Lib. But the nrf24 Can't receive data continuous.
if I Want receive 2th data , I must power up the nrf24.
This is my Code :
RFCTL...
hello,
I wanted an info which tool is better for debugging when using
native SDK.
do i have to use pyocd or openocd for native sdk hardware debugging
and if you can...
Based SDK 9.0 "ibeacon" example, nRF51822(QFAAG0) work's well when download the ibeacon.hex.
The target set as follow:
Based SDK 9.0 "ibeacon" example,nRF51822(QFABC0...
Anyone seen the new nRF52 online power profiler ?
It's an online tool that estimates the current consumed by your BLE application.
This allows you to better understand...
Hi,
Before starting advertising using advertising_start() function, if pstorage function is used to write data, then it gets stuck at that point as no pstorage handler...
Hello, I have an issue with ble_app_hrs_rscs_relay that doesn't seem to exist with the other sample projects.
The project compiles without any issues, but when I run it...
Apart from pressing Button 4 or adding a DFU service to current running application. Is there any way to enter DFU mode from application?
Is it possible with nrfutil to...