Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
I am trying the buttonless DFU example from SDK14.2.0. I am not following the testing procedure mentioned at infocentre for SDK14.2.
Followed test procedure:
1. Erase...
I've been using the nrf_twi_mngr_perform() function assuming that my transaction was complete when the function returned. Because of this, I felt safe keeping my descriptors...
Hi Sir/ Miss:
I've a custom peripheral heart rate device.
I use central example "ble_app_hrs_c" to connect it by PCA10040.
After I set up the service (Target_UUID) and...
Dears,
I'd like to add service while connection.
Now I am using UART service and want to add HID service when I put button.
How to add HID service while connection...
I am using Master Control Panel for doing DFU on nRF52832 DK. The nRF52832 is having example dfu code dfu_test_softdevice_w_bootloader_b_s132.hex from sdk11.
nRF51 dongle...
Dear experts,
I'm a new user of NRF52 technology and I use:
Keil µVision v5
NRF52832 (PCA10040)
Keil software pack 8.15 from Nordic Semi
debugger Cyclone...
Hi Nordic
I am porting an application from the EM9304 SoC to the nRF52810.
In the old application it was possible to send 26 bytes of manufacturer specific data (plus...
Hi,
I use BMD-350 on NRF52832 with SDK v13.0.0
I configure my radio to run the BLE at -20dBm power through the API sd_ble_gap_tx_power_set()
But few seconds after starting...
Hi!
I once set up a simple project using SDK 12 and the HRS example.
Now I tried porting it to SDK 14 and SD 5. That didn't work out well.
So I started things from...
Hello everyone,
I am working with TWI and broadcasting of data using ble_app_beacon. I am facing a problem in broadcasting of the data. I have complied the code and it runs...
Hello everyone,
I am working with TWI and broadcasting of data using ble_app_beacon. I am facing a problem in broadcasting of the data. I have complied the code and it runs...
Hello, Nordic.
I use NRF51822. I know NRF52 series is able to NFC Tag with Antenna.
But I want to use NFC module with NRF51822. If I can modify NRF51822 circuit, is...
Hi DevZone,
I am doing my project base on SDK 14.2.0 example spi. I modified the PIN according to Arduino PIN map and connected the nRF52480 Preview DK with Arduino Uno...
Hi Everyone,
So I have a custom board with an LED on P0.9. I have confirmed it works by applying power to it, so no issue with the LED itself or the way it is connected...
Hi,
My problem that the RAM is insufficient for my project.
Please, I want to know how to set optimization configuration. By the way, my central device only connect our...
