I am trying to setup SPI00 as SPI slave on nrf54l15 but not work as expected.
My board configure is like
and c program like
The program intends to use nrf54L15...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
I'm currently testing a custom board using BSP_SIMPLE defined in my board header file.
This is failing to build due to undefined BSP_LED_APP_TIMERS_NUMBER.
Appears to...
I have added a power amplifier in nrf51422, but I don't know when I should enable/disable the power amplifier in order to reduce power consumption, i.e. when listen for scanning...
Hi,
I try to compile example application (ble_sdk_app_beacon) and I have error on linking objects.
My include section:
#include <stdbool.h>
#include <stdint.h>
#include...
Hi,
I'm trying to get a modified version of the serial "NUS" service to work encrypted with Android 4.4 (API 19). Everything works fine on iOS, but with Android I get ofter...
hi,there
raspberry can ping6 pca10028, rasberry can receive udp packets from pca10028.
but how can i ping6 pca10028 from pc?
env: pca10028 + csr ble dongle + raspberry...
i'm confused of the relationship of wirepas and ant+,both claim to surpport mesh network and multihop.what's more confusing is that both are promoted by nordic.
I look up...
I find in the following example code that if I start my application from a powered-off to a powered-on condition and main() executes the code as shown, everything works fine...
Hi,
I do receive undefined HCI errors in my disconnection handler. I wait for the BLE_GAP_EVT_DISCONNECTED event and use the bleEvent->evt.gap_evt.params.disconnected.reason...
I've been reading through the documentation for pstorage but there's one term I don't understand
devzone.nordicsemi.com/.../a00131.html
What is the purpose of offset...
We are using two GPIOTE inputs and there is only 1 GPIOTE interrupt handler.
One of the GPIOTE input is from a power line chip that toggles @ 50 Hz rate. This GPIOTE input...
Hi Team,
I was trying dfu to load my application.
Edit #1
I have flashed softdevice.
Then I have compiled the example project 'dfu_dual_bank_ble_s110_pca10028...
I have an external temperature on my nRF51 DK. I would like to read the value of the temperature on my mobile device(Android).
I am able to read the temperature on the...
I would like to use the single shot timer and when the timeout handler is called, I would like to set up the same timer again with different interval this time. Do I have...
There seems to be a discrepancy between the 8.0.0 softdevice release notes and the product compatibility matrix. I would like to know if it is possible to use 8.0.0 softdevice...
