When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
We get the following assertion during startup if we include uart2 in the DTS.
*** Booting My Application v2.1.0-dev-ae1ee57f3906 *** *** Using nRF Connect SDK v3.0.1-9eb5615da66b...
Dear DevZone,
While reviewing the implementation of x509_crt_verify_chain() in C:\ncs\v2.9.1\modules\crypto\mbedtls\library\x509_crt.c , I noticed that certificate expiration...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
Hello,
I have the nRF7002 DK, which includes the nRF5340 (App + BLE cores) on-board.
The hardware requirements do not list this DK as usable for the course, which seems...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
Hi, I have two firmware images: A and B which I need to make compatible for OTA (DFU over BLE using MCUBoot - the standard process described in the devacademy course ). They...
Hello,
I'm trying to enable RTC2 for nrf52840 DK to use as a date time clock and set/get over SMP protocol. RTC0 is used for MPSL, RTC1 is used by the system.
I configured...
Hi everyone,
I’m using a custom board (a tracker) that can travel at speeds up to 65 km/h and transmits data regularly every 200 ms. I expect, therefore, that the inactivity...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
Hi
I am using nRF52840 with SDK 15.3.
I have a project where I uses FatFS to write to a SD-card with SPI interface (SPIM3). This works very well.
I am now trying to...
I'm currently working on implementing OpenThread on our custom board based on the nRF5340 along with the nRF7002. While building the project, I'm encountering the following...
Hi
Does the nrf-sw-pwm driver work on the nrf54l15. I am porting code form the nrf52840.
My output does not toggel, 0% and 100% does work but noting else.
I am using zephyr_nanopb_sources to add some protobuf files to my app target, and this works fine in a normal build without mcuboot. However, when building with mcuboot it...
