Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
Hi,
When erasing one page flash for responding one GATT request, it always went into assert_nrf_callback and has to reset the app. So I have to disable SoftDevice before...
Hello,
I am going to start programming BLE application, and I would like to know which enviroment is best to program it. Are there too many differences between programming...
Hello
According to the documentation the optimal CPU frequency is 16 MHz, Please, could someone tell me if that is correct or not?
Thanks for your help
Hi,
I modified the ble_app_hrs sample application with one custom service which includes, some custom characteristics (128 bit uuid), Now the problem i am facing is, i am...
Hi,
How to implement the passkey authentication, we are using nF51822 evaluation board. Is it possible to display the passkey using master control panel? And, we also don...
Howdy,
In a similar vein to my recent question about production programming....and nothing to do with takign an nRF51822 out for a walk :)
We'll write a simple test...
Hi
Before, TX and RX functions run well at iOS6. After we updated to iOS7, RX still worked but TX couldn't send out data. Did you verify nRF UART app at iOS7?
I'm reseaching a tag in low energy-cost using the nRF24le1.Till now,I can receive the message from the tag successfully, but can't send the command to the tag to read or write...
hi,
Now,my pre-Develop product(BLE),that to measure the Tx transmit power not correct with my setting(default 0dbm).
so,i have program a project for to sure the reason(Hardware...
I need to connect an I2C/TWI device to the nRF51822. The I2C device is running at a fixed 3.3V (from a boost DC/DC), but the nRF51822 is powered directly from a CR2032 battery...
Hi,
Is there anyway to keep the RTC going while in reset, device sw has crasched or in powered off mode or would I need an external RTC for this?
Is there any possibility...
I have two NRF24L01+ devices. My aim is to have one as PTX and the other as PRX replying with ACK_PAYLOAD. It is working with ACK enabled (without payload). However when ACK_PAYLOAD...
I'm interested in using the master emulator to connect to multiple target devices, but it does not appear there is support for this in the API (v2.1.3). For example, there...
