void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have started development on the nrf52832 development kit and i own a MacBook pro with mac os. I also have windows installed on my MacBook pro but since I do not have...
Hi I'm doing a school project where I'm going to make a bluetooth mesh network where I use nrf52840. where i tried to get "light_switch demo" to run, but i have some trouble...
Hello,
Could it be possible to do an update with a zip DFU file stored in a flash memory ?
What is the best way to do the modifications (mainlines) ?
Thank you
Hi,
I'm using two nRF52832 (SDK14.2, SD132v5) to send data via Notify to one central. This central can be either a laptop or a smartphone.
The two nRF52832 has the same...
Hi all,
I am using nRF52832 SoC and nRF5 SDK for Mesh v1.0.1. I know until now there is only support for relay feature in the Mesh SDK. I want to implement low power feature...
Hello,
I was trying to connect my boards to nRF Cloud to evaluate it. Setting up Gateway on the phone and on the web at nrfcloud.com was rather easy (just following getting...
I use the SDK9.0，When a bluetooth device and android APP to connect, disconnect the bluetooth device power, why wait for 20 seconds, the APP to detect device has been disconnected...
Hello Everyone,
I want to know that i purchased NRF51 DK ..which includes PCA10040 IC.i'm using MDK ARM KEIL5 . now if i'm going to develop one BLE product so i don't know...
Good morning.
I have two nrf-51 boards and a mobile device, the SDK that I´m using is the v.12.2.0. I need that the three devices are connected at the same time and its...
Hi all,
My configuration:
nrf52832
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using th e secure bootloader example located at \examples\dfu\bootloader_secure_ble...
The nrfgprgret register is used from the application(custom) to trigger the system into dfu mode. The nrf 52 enters dfu mode and a zip file containing bootloder.bin/.dat and...
hello, I check the standard example nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs device nrf52DK PCA10040 V1.1.1 ARM Compiler :...
I am currently considering purchasing the UBLOX NINA-B1 module. This uses the Nordic nRF52832.
The very 1st thing I wish to do is to be able to send and receive information...
Hi Nordic,
I have managed to make a board which has both the nRF52 and PN532 modules on the same board (picture) , connecting it through I2C as shown on the example here...
