Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
What's the maximum current for nRF52832 when only CPU is running from RAM at 64MHz (DCDC 3V condition)?
From Product specification v1.0 page 18, does the value "3...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I'm trying to set up DTM environment with my DUT(Own device, using nRF51822) and a nRF51DK for Lower Tester, referencing the document, nAN34_v1.0, "Setting up production test...
Hi ,
I am programming nRF51822(s/n 681859006) on my company's custom board, I am using the softdevice (s110_nrf51_8.0.0_softdevice.hex) to program it.
After successful...
Hi!
I'm compiling with 'GNU Tools ARM Embedded 4.9 2015q2/bin/arm-none-eabi-g++' and optimization -O0 and debug level -g3, nRF5 SDK version is nRF5_SDK_11.0.0_89a8197....
Hi,
I developed an application with nordic NRF51822 using SoftDevice S110 8.0.0.
The APP developer for iOS tells me that the app disconnects after about 2 minutes, while...
Dear all
I have a question about using nRFgo studio to Program Application
I have develop a nRF51422 central project for a few month using nRFgo studio.
The nRFgo...
Hi everyone. I'm using nRF51822 and try to work with Eddystone protocol. I use experimental_ble_app_eddystone and my beacon work properly. I validate it via nrf Master control...
Has anyone else encountered a recent problem while compiling projects using mbed online compiler (error message goes "Struct "" has no field "NRFFW" "RF_UICR->NRFFW[0]" in...
I am trying to implement a OTA DFU in my project. The DFU Examples given create a bootloader file of it's own and starts transmitting in the nrf51422 dev kit(DFU_Targ, ble...
Hello,
Platform nRF52 with SDK 11 (S132)
I use nrf_drv_spi_init to register a Handler (used for screen and SD card so it can be long)
I have sometimes crashes when...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
