Hi DevZone Support.
We've been impressed by Nordic's Edge AI Lab & sdk-edge-ai addon and are looking to use it's models & runtime in our products.
Based on the documentation...
Hi,
Using nRF Connect SDK v3.3.0, Toolchain v3.3.0, nRF Connect for VS Code 2026.7.2128: I want to configure maximum transmit power used by the nRF52840 on a nRF52840DK...
When performing a OTA update with RPA enabled, the dedicated DFU app, nrfconnect app, and nrfutil.exe fail because after the buttonless bootloading has been enabled the device...
HI ,
I wan to disable the vBus "VBUS is not valid, and the pull-up resistor on D+ is disabled." on nRF54LM20,
I try to write to disconnect usb from PC :
NRF_USBHS...
Hi Nordic Support Team,
We are working on an nRF5340-based application using the nRF Connect SDK and would like to implement FOTA for both the application core and the network...
hello! I'm having problem when trying a repairing after clearing the bond information in the nrf52840 i using pairing via oob , i exchange oob between nrf52840 and RPI using...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
Hi ! I have attached the PCB design and schematic provided by Nordic for nrf52832 which is said that its also same for nrf52810.
I wanted to use the nrf52810 board for beacon...
Hi all, i'm Duy
I'm doing my thesis project about Bluetooth mesh. My board is nrf52832 custom board which is similar to pca10040. i want to build a mesh network with several...
Hello, I'm able get an updated battery service value on nrf connect using the 15.2 s112 proximity example on the DK using a cr2032. Then adjusted the clock to LF RC and removed...
Hi,
Let's say I have a door lock module without user interface... no keys nor display but with bluetooth peripheral module. The user pays is room via the application then...
Hello,
I would like to know if it's possible to simply configure all parameters for a BLE connection by a PC software.
The goal is to manage the BLE parameters to measure...
Hi,
I want to create 1 hex file that will contain my bootloader, app and softdevice.
I know i can use NRF GO studio in order to read each hex individualy but it is of...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
Hi,
we are testing nrf52840 together with rfx2411n amplifier to extend the range.
The problem is that we have same range and same RSI values when testing with bypass mode...
Good afternoon,
I have purchased multiple nRF52840 Dongles and so far have successfully ran blinky peripheral and master (required to adopt PCA10056) examples.
I tried...
