Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
I'm using Ceedling, Unity + CMock to implement unit tests but I'm running into issues when it comes to mocking nrf_drv_gpiote.h.
I'm trying to test a file, call...
Hi Nordic Engineer, I refer to your previous post title "Running micro-ESB concurrently with BLE" and gonna to use it on our project.
I test it on 4 pcs of DK board, found...
I have a problem using ble_advertising_restart_without_whitelist(). According to the documentation (as I understood) it should start advertising without whitelist even if...
Hi all
When i am reading ANCS code, i have some questions. SDK 12
Question 1: when ble device are connected with ios, the pairing is wrong, how to handle validation...
I am attempting to port a custom ble service from sdk12 to sdk 14 and am a bit confused as to how to increase my uuid count. In sdk12 I did it like this:
uint32_t err_code;...
Hi
I am using wireshark 2.0.1(64 bit).When i am trying to capture the ble packets it showing error.I have attached the Wireshark error message.BLE Sniffer version 1.0.1.I...
In the Bluetooth Light Controller example for the client in main.c these constants are defined:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
Why...
Hi Nordic,
Sorry if I missed and repeated a question, just point me to the previous answer if it has been posted before.
I am trying the DFU example found in the SDK...
Hello,
I'm wondering that it is ok to route ANT line through board-to-board connector to chip antenna.
Because there is no space to place nRF52832 and chip antenna together...
Hi,
I've seen that SDK 12.3.0 contains a new version of the application sample using the Eddystone protocol for BLE. I would like to know if this version is compatible...
I am using the template example for S130(works fine).
I tried adding a simple Pin interrupt on the code but it didn't call the pin interrupt handler everytime I press the...
For applications using the application UART Module ) via APP_UART_FIFO_INIT() without hardware flow control - how does an application put the UART peripheral to sleep?
...
Hello Nordic staff (or anyone in the know),
I saw this post from @newtom almost a year ago which concluded that I2S master library does not support 32bit words from mics...
Hello there,
I am a beginner, i want to know what changes should i make in the already existing example "ble_app_uart" so as to make my nrf51 development kit able to transfer...
