Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I am working on a custom I2C bootloader for nrf52832 using SDK 14.2.0. Currently, the bootloader can flash the application code very well. But I have no idea how to flash...
nrf_soc.h in these distributions reference symbols like SWI2_IRQn which aren't defined unless the build includes nrf51_to_nrf52.h, something I try to avoid when building for...
Hi, I'm working with nRF52832/nRF52840 and SDK 15 or 15.2 on Windows with Segger Embedded Studio.
Is it possible to use the device in low power mode, but keeping active...
My nRF52840 Dongle appears to have failed while its boot loader was being updated, the led does not flash red like it used to and only gives a short white flash on plugging...
Hi, everyone,
We are developing the BLE project on nRF52832 chip by using RTT / UART logging. Previously we monitored the project via UART communication port. But than we...
Dear Team,
Can you please review the attached schematic of NRF51822 used with matching Balun and chip antenna.
Balun: 2450BM14E0003T
Chip Antenna: 2450AT18A100E...
I have an application running on an nRF52 with the S332 softdevice which is a server which exposes a a few services each with a few characteristics. I am using the Nordic...
Can the nRF2460 be operated with TXLAT (0x52) set to a value lower than 4 ?
Can the nRF2460 have a lower latency than 20mS ?
The range requirements are very small (30...
Hi All,
I have created a custom board header file based off of the pca10040.h file. I have customised this to support 10 buttons and 2 leds. I have also extended the array...
Hi everyone ;)
I have a problem with timeslot ESB library with Bluetooth LE. In my application i need do somethingh like that:
Bluetooth and ESB PRX works excelent...
Hi, I am using the BLE mesh 2.2.0 with nRF5_SDK_15.0.0_a53641a. I am using Segger embedded studio as toolchain. I was able to compile and flash the default app code onto NRF52...
I am working on an application to connect approximately 500 devices in a single network... trying to check if Thread or Mesh is a better option... Please do suggest...
After searching around a little bit I found this post, but sadly an answer did never come up apparently. I'm using the nrf52 DK, using the 132 Softdevice.
I'm kind of at...
