Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
When using my mobile to make provisioning with the GATT provisioning example for the light switch, is the mobile a node? Does it get the messages as well? Does it work as...
I'm under the impression that this piece of the given example is an interrupt handler. Am I correct? If yes, then there another snippet:
So, is there a while loop inside...
Hi All,
I am facing problem in my bootloader linking please see below
Linking target: binaries/bl/bootloader.out /tmp/cc9UGLw7.ltrans4.ltrans.o: In function `nrf_svc_handler_c...
How do you think - is there resources enough to add SPL (sound pressure level) measurement functionality into Nordic Thingy:52? Is microphone appropriate or may be external...
Hello, I'm using the example package Nordik_Mesh_V2_0_1 \ nrf5_SDK_for_Mesh_v2.0.1_src \ examples \ light_switch, and I would like to extend the number of servers from 4 to...
I'm trying to understand the cost differences, and pros and cons between:
A) creating a two chip solution - Using a BLE module - PLUS an second micro that runs my application...
I am in the process of trying to send live data from a nrf52 board over bluetooth to another nrf52 board using the example projects ble_app_uart_c and ble_app_uart. We are...
Hi,
I use SDK 12.3 to run experimental_ble_app_buttonless_dfu on nrf51822 after reference this blog , but still can not work.
It works fine with PCA10028 board.
I want...
hi :
i send characters of SPI master of 52DK to SPI slave of our target board(Nordic nRF52832), our target board use SDK v12 spis example. but spi slave event can not rececive...
I am using SDK 12.3.0 and S130 2.0.1.
In example ble_app_uart and ble_app_uart_c,
Central setting:
Peripheral setting:
Why it took so long to discover service...
Using the same connectivity firmware, a dfu update using nrfutil takes about four times as long as the same update using nrf connect. I have to setup dfu updating in a production...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
Hi,
I am trying to use Segger embedded studio for my project,
I get these errors:
Building ‘ble_app_uart_c_pca10028_s130’ from solution ‘ble_app_uart_c_pca10028_s130...
hello,BPROT does not work normally when i am debugging BPROT.
when i set CONFIG0 bit2 to 1,that is NRF_BPROT->CONFIG0 = 0x00000004,then i want to erase block 2(start address...
