My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
Hi, I can normally log with NRF_LOG_INFO(). But if i enable softdevice (bluetooth stack init) logging stops working. Interesting part is that there are several log lines before...
BLE Control by Main CPU (MCU):
1. How the MCU communicates with BLE HW?
2. What is the amount of MCU performance is required to control the BLE? (expected answer example...
Hi nordic.
I use SDK 14.20 and nrf52840 board and s332 softdevice.
Our app has to use ant+ and ble.
My device connect with app.
App requests device to ant+ scanning...
hi guys:
When I was using mesh sdk, there was an error in compiling.
I use examples\light_switch\server\light_switch_server_nrf52832_xxAA_s132_6_0_0.emProject
I am...
Hi,
I am using SDK 14.2 -> BLE peripheral proximity example. I was trying to add a custom service and some characteristics to this proximity example. I basically took the...
Hi, I have two strange problems regarding the NRF_LOG. 1. In a for loop, char string that has changed is not printed out as what it contains now, it is printed out as what...
Hi,
i have purchased the following module
However, after connecting the VCC and GND to 3.3v DC supply the module is not detected. My questions are :-
Does...
how to slove it
1> Linking light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0.elf 1> build/light_switch_proxy_server_nrf52832_xxAA_s132_6.0.0_Debug/obj/ses_nrf52840_Vectors...
I am using the nRF52832.
I want to go to sleep in absolute lowest power mode possible that still allows a timer for wakeup. Using LFINT.
I don't need ram retension, etc...
Code example: nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_ble_uart_freertos
Board: custom board with nRF52840
What are the fastest and easiest steps to make this...
Hello,
I am trying to code nRF52840- DK with MAX30003 ECG Board Using SPI. I have referred Arduino Uno Code for MAX30003 ECG.
I need some help for Driver Development if...
