Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
I need to transmit and receive beacons using nRF51 DK. I saw a few examples in the SDK ble_beacons where we use the app, but I need code to transmit and receive both using...
I am trying to send 'h' or the number 1 using vendor defined page (custom HID descriptor). How do I do it?
NOTE: I have worked with hid mouse & keyboard examples and also...
Hi,
I am trying to make a network of four Nordic Thingy: 52 IoT Sensor Kits by using the nRF52 DK to program them. Then, the readings for the 4 senors should be displayed...
Greetings friends,
I'm having some trouble figuring out how to use the the sdk for developing a beacon central.
What I've got so far is: I used the BLE Central for UART...
Dear Sir/Madam I am currently designing a IOT board using nRF5284 as the main controller IC The board is battery powered and is charged using USB. Data can also be transferred...
We're seeing an issue where a dfu package containing SD+BL+Apps gets stuck on iOS nrfToolbox during DFU process after it updated the first part 1/2, which is BL+SD. The same...
Dear Nordic Team
I am developing a BLE device using the following resources:
- Microcontroller: nRF52832
- Softdevice s132
- Peer Manager is used for whitelist...
Hello,
I have developing one project in that i am using nRF52832 and SD 15.0. Here is the current application developing:
There are 3 ble app_blinky(ble peripheral)...
what do i need to modify in an application to send that application over mesh? Lets say i wan to send blinky example over mesh to all other nodes, what i need to change in...
I am using the mesh SDK 2.1.1 and have one node that uses the serial API. That node sends mesh packets to the network via the PacketSend serial opcode. This command uses an...
