Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi!
I have questions for Nordic developers team. What capacity of network is possible with nrf52840 thread mesh? I've tried to attach large amount of nodes to mesh and...
Hi Guys,
I want to use the TWI for my mesh application in which I want to read out 2 sensors (Sensirion SHTW2 and SGCP3) and then send the sensor values over a mesh network...
Hi all,
I´m using nrf52832 with sdk 14.2.0 and softdevice s332.
I have opened and closed the eclipse. Now when I open it, it compiled and gives me this error that I did...
Hi,
I am using nRF_SDK_15.0.0?a53641 and writing a program with keil.
I am trying to read data from the acceleration sensor( LSM303DLHC ) by communication with BLENanov2...
Hello
I just started learning nrf52832 DK and run few of the examples. I wanted to start developing my own application based on the examples. Right now, I want to read...
Hello, I have some confusion about updating advertising packet dynamically.
I am using nrf52832 with SDK v12.3.0. I am sending datas from sensor in advertising packet(manuf...
Hi,
I am trying to build the ble_connectivity code "ble_connectivity/pca10040/ser_s132_uart" to test the serialization part. The scan is not working. I am using PCA10040...
18.9.13 RAM[0].POWERSET (and sections associated for other RAM sections) states:
When read, this register will return the value of the POWER register.
however the...
Dear Sir,
I was using my Rigado BMD 300 and it was working fine.
When I open the nRFGo Studio the following was the details displayed in the tool.
But sometime after...
Hi there,
I am struct for two days trying to send 6 packets of 20 bytes as central. I use ble app uart central sample from nrf5_sdk11.0 with nrf51 S130 v2.0 softdevice...
Hi,
Does anyone know how to receive voice data from Nordic 52832 remote control in embeded linux ? Does Nordic provide any package for this purpose ?
Thanks
Hi, everyone,
We are developing the project on nRF52832 chip that is built from master (multirole) and slaves modules. The master program (in our case master is multirole...
I want to send data to all node by mesh 2.1.1.
From the Mesh profile(3.4.2.4 Group address),the dst_addr = 0xFFFF is send to all node .
I try to setting "packet_tx()"funtion...
Hi,
Currently im working on creating firmware for out device based on the nrf52832. I have structured my project where i have seperate files for each module i am creating...
The hid keyboard example includes the battery service. But how does it work? I would like to monitor the battery charge. After I use the voltage divider, to which AIN pin...
