Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
Hi
This is a heads up that in SDK15.2.0 and file nrf_esb.c you have the line
m_rx_fifo.p_payload[m_rx_fifo.entry_point]->rssi = NRF_RADIO->RSSISAMPLE;
it should actually...
Hi
My application uses NFC for various reasons, and I need, at runtime to load up to 4 textural NDEF records onto the Nordic NRF 52832's NFC hardware.
If I wanted a simple...
Hey there faced with the following problem:
I have two hardware setups:
1. Laird DEVK-654 (nrf52480) without external oscillator
2. Laird BL654 mounted to a carrier...
I added the Generic OnOff Model from the thingy52-mesh-provisioning-demo to the Light Switch Proxy Client example from the nRF5_SDK_for_Mesh and get a linker error for the...
Hi All, I am polishing the code that we have, working out minor bugs, etc, we use Nordic UART to exchange data between our device and smartphone or tablet, sometimes data...
What is the proper way to temporarily disable the softdevice? Currently I have the following
sd_ble_gap_adv_stop(); bool disabled_softdevice = false; if (nrf_sdh_is_enabled...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
Hi nordic members,
I am using nrF51822 board. I want to inform you that i am getting error undefined symbol: __data_start__ at compile time in segger embedded studio for...
Hi Nordic,
For battery_level measurement on the SDK we are using a timer such that for every 5 seconds or 10 seconds if the timer expires then the saadc will be triggered...
