Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Dear support team,
I'd like to provision a mesh node which is implement on thingy and without proxy feature.
As I know, the BLE device (mobile) should communicate with...
hello I am new on nrf52 and I would like to run the example for the ant+: "bpwr_tx".
I am on a nrf52832 chip (with a pca10040 1.2.4 demo board ), I am using nRF5_SDK_15...
Hello,
I used nrf52832 as a scanner.
Now i use it to scan only one tag. And the TAG advertise data addcoring to ble 4.0.
Now i find scan channels are not 37,38,39,37...
■Development environment nfr52832 SDK_12.3.0
■Question I'm making Central's module. After connecting with a peripheral of pairing finish, the function(pm_peer_rank_highest...
Hi all,
I am trying to test OpenThread protocol for an application that we have and we want to use the CLI interface as the application logic should stay in the application...
Hi all,
I was in the process of buying 3 nrf52-dk boards. I need to know if one can differentiate all of the different boards on their PC when connected at the same time...
Dear Nordic Team,
Thanks for support
Currently i am work with VL53L0X in ble_uart_app example. it working fine , but its take 5ma current. How can i use TWI in low power...
Hi,
I would like to know if you can sniff BLE packets with really low transmission power, for example can you sniff a -35 db signal with any average bluetooth receiver?...
I've used PCA10040 sdk15.0 example ble_peripheral ble_app_uart
I can handle it through terminal.
If I insert strings through terminal, App can receive.
But, I...
hii,
i am trying to interface the nrf24LU1+ and nrf52832. I wanted to know if i can program the nrf24lu1+ without the requirement of nrfgo motherboard. or is it necessary...
I don't want to use MESH， because there are too many data
Application scenario
Mobile phone ------------> DeviceA --------------------------------------> DeviceB
...
Hello,
Would there be any particularly adverse side-effect if two NRF51822 GPIO pins (e.g., P0.18 and P0.19) were shorted together? One of the pins (e.g., P0.18) would be...
SDK ：15.0.0
Examples：ble_peripheral / ble_app_uart / pca10056 / s140
Board：nRF52840 DK
After pairing, may be connected, because the indicator lights continue to shine...
Hi,
I am using sd_ble_gatts_characteristic_add to set a characteristic in my service. The function call return 0 - NRF_SUCCESS but when I browse the service with nRF connect...
