Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi everybody,
I'm trying to use the example ble_app_hrs with s110 on the PCA10001 Board and the ble_app_hrs_c with s120 also on an other PCA10001.
I changed some led flag...
I have already explored how to fix the related problem in the DevZone. I think the firmware of the ATSAM3U2CA-AU is erased. Here, I have two problems:
1, How can I get the...
Hi,
According to the code in PCA10059.h:
#define RX_PIN_NUMBER 11 #define TX_PIN_NUMBER 9
I would like to know what pins are related to number 9 and 11 in this schematic...
Hello,everyone.
If you have some suggestions,and you leave them, I would appreciate it very much.
I designed a pcb base on nRF51822. It can only be searched by mobile...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi, I want to reduce current my module.
I used SDK15.0.0ver, nRF52832
I have 2 questions.
1. I used app_uart_close();
But My module was reset again.
2. I want to...
hi...
i want to check my data for every minute , so i set the timer for one minute.
but its not working ....... how to do?
i have set the timer like below
i am finding...
Hello nordic team, I have a question regarding BLE Mesh and Uart0:
The InfoCenter is saying that Uart0 is blocked when using the serial Support. I don't wan't to use the...
Hi,
I'm testing an interactive pyaci example in Mesh SDK v2.2.0 with two nRF52DK boards.
Interactive mesh provisioning and configuration example worked fine so I modified...
I'm using nRF52+SDK11.0.0+S132 . It currently has SPI, SPIS, TWIM, RTC. I want to remove SPI and I'm getting: ..\components\drivers_nrf\spi_master\nrf_drv_spi.c(56): error...
Hello,
I'm using the nRF52 DK with SDK 15 and SD132 6.1.0. I have a custom service running that requires periodic characteristic writes. Occasionally when writing to this...
hi guys!
i'm trining to develop the nrf 52840 devkit in particular for the ble use.
from the documentation i didn't find anythingh about send a message to the dongle from...
Hello guys,
I am using nrf52832(PCA 10040) and transmitting radio packets. I want to collect the packets using raspberry pi. Is it possible?. If yes, how are the ways we...
