Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
I'm following the Border Router Quick Start Guide . In it, it states:
To change the settings, edit the /etc/config/thread_border_router file.
However, that file...
Dear experts, please tell me, how can I switch the frequency source for the RTS from STAL to internal RC generator when the processor is running? command sequence does not...
Hello,
im using nrf52832 NRF5 SDK 12.2 , S130 . using the pasted code and i get 1023 on the ADC even voltage is 1.7 volt i using keil ver 5 s130 i double checked the voltage...
Hello,
I have prepared an nRF52840 with DFU example (dfu_nrf52840_xxAA_s140_6_0_0).
When making the DFU package for the blinky example (bin/blinky/blinky_nrf52840_xxAA_s140_6...
Hi all,
I'm working with 2.1.0 version of Thingy:52 firmware (the last version currently). Further I am working on Linux with SEGGER J-Link Commander V6.34c in order to...
Hi,
I want to read register 0x00 (chip ID) of ads1292. i do following...
===========================================================================================...
Hi
I am developing 4 layer PCB for the nRF51822 with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003) with...
Looking to apply an nRF52 chip in a wearable device... ideally without mounting it on a board.
Is that remotely feasible?
It would still be necessary to connect to 12...
Hi to all,
i have a project that was based on SDK 13 and in that version i had a bility to call fds_record_write with multiple data chunk, but in softdevice 14 and sdk15...
I have integrated the code of the multilink into the uart central example. The project can be built without error. however, it is not possible to establish a connection to...
Hi,
I'm starting development of a new product utilizing nRF52840 mcu. We used this chip in previous product with Bluetooh stack (SoftDevice). I didn't participate on this...
Hello!
Since the code of nRF connect code is open (on github) - is in possible to extend supported devices list? In other words, is there any way to use non-nordic boards...
I would like to know if you can create a mesh network with nrf52840 preview DK?
Would you have a problem with this board?
currently, would a better option create a...
Hi,
Using the reference schematic No.4 given in the NRF52840 datasheet I made a design. I was able to test all the peripherals and range testing without any issues. But...
