I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
Hello! I trying to send message from peripheral to central. On peripheral characteristics are changes with delay. To change characteristics I use this function:
void send_char_data...
Im using the PCA10031. Placed it in the my laptop usb and installed the nRF go and keil mdk arm and nrf51 sdk.
Using the pack installer, which example should I use to be...
Hi,
Can anyone tell me, how the handle value is assigned for a profile. In my master control panel i can see the handle values assigned for every services, but it is not...
Use the beacon want to send with the temperature and remaining battery power.
But beacon of UUID, Major, Minor, Type, etc. The only information in the beacon 26Byte.
...
Hello,
We are developing an application which is using the app_scheduler (especially to put events etc.)
It seems that sometimes (very rarely) we detected a Hard Fault...
I have 4 buttons in my circuit with a nRF51822QQAC (a RAYTAC MDBT40 module on a custom PCB), I am using a very simple printf to check which ones are pressed, the internal...
I've followed this for assistance, but I'm stuck:
https://devzone.nordicsemi.com/question/17846/nonvolatile-memory-access/
I can read from flash, but I can't write to...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
I went to so many references and definitions of variables and functions but I can't seem to find where is decided to use either spi_master_0 or 1.. where is this magic config...
I am a freshman. And I am doing some research on BTLE by nRF51822-EK. I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Is there...
Hey,
For my project I wrote and tested (w/ nRF51 DK) all firmware in mbed. I also made a custom PCB w/ the nRF51822 CEAA chip based on the 4 layer reference design provided...
HI,all!
I want to know if BLE can send data to APP in form of String instead of Byte?(the examples all send in form of byte )
If it does can, can you mainly introduce...
Hey everyone,
I'm trying to print floating point numbers to the UART to debug my application. I know the nrf51 is doing the operations correctly because if I convert the...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
